710at420 THC Extraction
710at420 concentrating forums for information and topics on the extraction of THC and other associated cannabinoids within cannabis
Subforums
Discussions and topics specifically about using medical cannabis tinctures and other extract formulas for medical cannabis use, dosage rates, which strains work best for what etc.
42,130 visits to this link
238 topics in this forum
-
- 1 reply
- 743 views
Has anyone ever tried this. It would probably work well since the butane is sloshing around the leaf etc. instead of it just flowing over it as in the normal method of extraction. It wContributed by: Nugg [Editor's note: use Copper pipe, Stainless Steel, or Glass ONLY for your extraction tubes. Avoid ALL plastics, brass, steel and galvanized steel pipe - these materials can contaminate your oil & make you sick. All types of extractions should be done outdoors or in very well ventiltated areas. Take safety precautions - no smoking, wear eye protection and gloves.] Nugg read this post at cannibus edge about making hash oil from butane. There were ideas of run…
Last reply by Chev, -
- 1 reply
- 615 views
if i made some honey oil with about 1/4 ounce of weed (and used a smaller extracter than usual) would it work as well as it would if i used an ounce?
Last reply by pipeman, -
-
- 420 Crew
- 4 replies
- 914 views
Does anybody know an efficient way to make oil and how much chemicals you would need for 40 lbs of leaf?
Last reply by red dragon, -
-
- 4 replies
- 996 views
I remember when i was younger i cleaned quick start fluid for diethyl ether. Would this work for naphtha??
Last reply by Bling, -
- 3 replies
- 1k views
i was thinking about making some hash oil and i was wondering how much does average stuff sell for
Last reply by pipeman, -
- 1 reply
- 535 views
Ive got about 150 grams worth of weed and im gona make a few batches of oil. only thing is....tons of fucking seeds.....how bad is it if i leave the seeds in when i do the butane extraction? any one know how this affects the final oil? does it add some thing bad, or just add a little unwanted junk? and if i have to....any original ideas on how to remove masses of seeds?
Last reply by pipeman, -
- 24 replies
- 1.7k views
Ok, I was gonna do a detailed thread but flipster had the same idea and did a way better job than i would so i will be breif. 1. Got together what i needed
Last reply by red dragon, -
- 4 replies
- 889 views
I just made some hash oil using the butane extraction method (easy, and i got quite a bit of oil). i want to know more about isomerization. i keep reading conflicting reports. some say to use acids and some bases.... can some one that has actually done this procedure please give the instructions?
Last reply by Luke Skywalker, -
- 2 replies
- 597 views
as i posted already i did the Butane extraction process for the first time the other day. worked wonderfuly. now, ive messed about a bit with chemicals and minor messing about with home made explosives. but this process.....must of been one of the most dangerous things ive ever done. (potentialy). now, ive already looked into other gases (non flamable) and have come to the conclusion that butane is the best (boiling point, cost ect..). so....i want ideas on how i can put together a setup that will be "stand alone". so that i can just start the process and leave it to do the rest. clamping down the pipe with the weed is no problem. but.....how to i make a device that w…
Last reply by Luke Skywalker, -
- 10 replies
- 2.2k views
been reading up on oil extractions. The first step is the basic extraction, whether it be butane, or reflux with a solvent. Then you can isomerizie the oil in a process utilising sulphuric acid, which not only increases potency significantly by converting the cannabidiol component to THC but also changes THC to a higher rotating isomer of itself, basically creating a product with a much more pronounced psychadelic effect. Then there is THC acetate, which has an even further improvement on potency and psychadelic properties of the oil. However this process utilises Acetic Anhydride which is extremely dangerous and requires an artificial atmosphere to be created insi…
Last reply by Deemz, -
- 0 replies
- 561 views
I haven't seen any one hear talk about the mirror test. The mirror test is to test for any residue in the butaine. HOW TO DO THE MIRROR TEST 1 squert some butaine on a mirror 2 wait for the butaine to evaporate 3 look for a white smelly residue (don't mistake it for water condensation) if it has got a white residue DO NOT USE it will make you sick or build up toxins in your body
Last reply by tripy spiral, -
-
- 420 Crew
- 8 replies
- 1.1k views
to use my old 400watt light bulb to do butane extractions. so tell me, am I crazy?
Last reply by pipeman, -
-
- 4 replies
- 961 views
This is an answer to a question asked here some time ago: THC Nose Drips - eucalypt oil (u can order it at your local drug store, do not mistake it for camfor oil they are very different) contains certain chemical agents that increase very much the skin and mucous penetration for lipids and neutral molecules (like lydocaine base in local contact anaestetics). - mix warmed eucalypt oil with hash oil until u obtain liquid consistency and put it in a nose drip used bottle (it is also best for massage and other local aplications). - use one or two "puffs" for every nostril and wait a few minutes - TAKE CARE: too much use (seve…
Last reply by flipster, -
- 1 reply
- 558 views
Does anyone know how i can turn a crudy lump of hash into honey oil using butane, I really dont like the taste or smell of the stuff but im hoping to extract the thc,I've done a little with regular weed, but not sure how to handle a lump of hash in my extraction tube. Im never making solvent hash again, its gross.
Last reply by pipeman, -
- 5 replies
- 664 views
Hello everybody I decided to register at last because I want to share my latest idea and see what u think about it: - I don`t know if you have seen those soda refilling bottles. They are actually normal Poly Ethylene (PET) 2L or 1,5L or 0,5L bottles - you know the ones used for Coca Cola and Sprite etc that u find every where now. - U can find in stores heads with a soda dispencer valve that u can put instead of the plastic bottle cap of the used CocaCola PET and what u get is a refilling soda (artificially carbonated tap water) container. This refilling bottles are wery popular here, because the "mineral water" obtained like this is very cheap. - My uncle had a smal…
Last reply by misstress morbid,