Cannabis Paraphernalia

Righto. I got a jar and took the lid off and torched it red hot all over to remove paint and fumes from heating then scrubbed with brush underwater to remove soot and repeated heating/scrubbing, this will be my heating plate. I then used a glass drillbit to put two holes in the bottom of the jar. I inserted small diameter black garden hose into one of the holes to suck vapor, the other is the carb. I then put a pinch of herb on the insid of the lid and screw the (upside down jar) onto the lid. To heat mabey a zippo or candle etc.

My new Syn, vid coming This is the smoothest tube I've ever hit, and talk about capacity, the beast holds 2 litres of GO . http://420downunder.smugmug.com/Other/Tubes/SYN/IMG0156/811942820_HnhyS-X3.jpg http://420downunder.smugmug.com/Other/Tubes/SYN/IMG0156/811942820_HnhyS-X3.jpg http://420downunder.smugmug.com/Other/Tubes/SYN/IMG0158/811942932_65xwJ-X3.jpg http://420downunder.smugmug.com/Other/Tubes/SYN/IMG0159/811943047_EEJ6b-X3.jpg http://420downunder.smugmug.com/Other/Tubes/SYN/IMG0160/811943133_jeVqd-X3.jpg http://420downunder.smugmug.com/Other/Tubes/SYN/IMG0164/811943563_AgJiv-X3.jpg http://420downunder.smugmug.com/Other/Tubes/SYN/IMG0163/811943418_LL…

Here's a little vid of mine, there's still more stuff on the way

I went about a month without cleaning my bong (which for me is a rare thing...I like that shit to be sparkly!) and it was looking pretty gross, so I gave it a good soak in metho, filled it with some rice and shook that thing around as I usually would, and almost all the gunk was gone. But, just below the ice notches, about level with where the "shotty" is, there's this light brown film. I can't physically get to it by any means, because the ice notches block all my aerial efforts. Anyone got any ideas? If it's going to be too expensive I'll just leave it, but yeah. Suggestions would be great

This is my new bong jsut got it from BnT. Its a beauty of a double chamber, so stoked with it. Almost happy my mate broke my old one cause he forked out for this baby. p.s - names doris Peace F D L

I have started saving up my grinder dust to press some hash... What is the best way to smoke this? I have tried a screen pipe before for it. I also have a vaporiser, but a cheapo electric one which has no whip/bags. It just heats up a small plate and air sucks in through the gap between the top jar and the base, doesnt seem very effective? I don't know. I have been looking around for a glass hash pipe/bulb but I have no idea about what design is best, with the least waste. Also kind of after one easy to clean so it lasts forever Many thanks

I purchased one of these around 6 months ago, have to say, best investment I have ever made. It really is perfect, portable and discreet. I have taken it to parties where while using it I have been asked what it is, beauty is I have never had to even speak when asked this as others will pike up with their guess such as breathalyzer. If I had to list cons for the Iolite it would be that it takes around 5 minutes to heat up, but personally this doesn't phase me.

hey guys, found this kool lil' tool at Joynt Venture in the Perth CBD, originally i just got it for the skewer to unblock the hole in my cone piece, but i recently started using it to its full potential, and i've found it makes the cone packing and cleaning experience so much easier! check it out.

Not sure if this was a dupe, did a search and found nothing so here it is. The Spilly Billy "'''Spilly... consists of five main components: Body (1), Base (2), Stem Camber (3), Screw Cap (4) and Shottie (5); Body & Base:The main body is secured to the base by a quarter turn taper locking system. A genuine Viton O-Ring creates the seal between the two parts. Stem Chamber:The Stem chamber slides inside the main body. Two fitted genuine Viton O-Rings sit above and beneath the top face of the stem chamber to create an airtight seal. Screw Cap:The screw cap attaches to the threaded section of the main body, securing the stem chamber and sealing off the …

Hi guys Im new and recently purchased a new bong from roor.de, I have no idea how long delivery time is, Im in Australia and I am hanging to get this!!! How long have you guys had to wait to receive products from roor.de?